What did you do to your bike today?
- Thread starter Diluted
- Start date
TBR Exhaust
Power Commander V
Blue bar ends (I Should have gotten Black ones)
Black adjustable break/clutch leavers
PSR Block off Plates
K&N Filter
Wheel Stripes (a few days ago)
Marthy's 6R Viper Advgear RevB Fuel Map
Sorry shes a lil dirty and needs a bath
Power Commander V
Blue bar ends (I Should have gotten Black ones)
Black adjustable break/clutch leavers
PSR Block off Plates
K&N Filter
Wheel Stripes (a few days ago)
Marthy's 6R Viper Advgear RevB Fuel Map
Sorry shes a lil dirty and needs a bath
Last edited:
thread with photos please...
Very nice! If you partially remove your decals and add Decepticons ones, I'll know for sure that my suspicion that you're copying my bike is right.
Very nice! If you partially remove your decals and add Decepticons ones, I'll know for sure that my suspicion that you're copying my bike is right.
HAHAH my buddy wanted me to get autobots stickers for it!!! and i think my wheel stripes look better /tounge muahaha
and i dont think you have blue bar ends do yaaa
not sure about your leavers/wind screen
your tail light is crome
and i got ninja mirrors on the wayyyy
and i doubt you modified your TBR exhaust mount to make the pipe sit lower and not YANK up on the headers.... becasue TBR sucks at manufacturing mounts lol
You better watch out maybe i will 1UP ya with a power crystal replacement O_O
HAHAH my buddy wanted me to get autobots stickers for it!!! and i think my wheel stripes look better /tounge muahaha
and i dont think you have blue bar ends do yaaa
not sure about your leavers/wind screen
your tail light is crome
and i got ninja mirrors on the wayyyy
and i doubt you modified your TBR exhaust mount to make the pipe sit lower and not YANK up on the headers.... becasue TBR sucks at manufacturing mounts lol
You better watch out maybe i will 1UP ya with a power crystal replacement O_O
Well I'm sure you'll pass me by. All my modding money is going into this:
What now?
miketriebsch
New Member
TBR Exhaust
Power Commander V
Blue bar ends (I Should have gotten Black ones)
Black adjustable break/clutch leavers
PSR Block off Plates
K&N Filter
Wheel Stripes (a few days ago)
Marthy's 6R Viper Advgear RevB Fuel Map
Sorry shes a lil dirty and needs a bath
Hey was it just me or was that k&n a pain to get those two clips in? Lol I had to walk away a few times afraid I might just throw the darn thing away lol
no the K&N is a B*tch heres the key
figure out how i goes on the stock filter
grab one side have a buddy grab the other
each of you only work on your one side but do it together in one motion just like you were each putting in a stock filter solo
and pop it snapped right in first try together lol
figure out how i goes on the stock filter
grab one side have a buddy grab the other
each of you only work on your one side but do it together in one motion just like you were each putting in a stock filter solo
and pop it snapped right in first try together lol
Last edited by a moderator:
miketriebsch
New Member
Yeah well I was doing by myself and holding the gas tank up by shoulder and it was dark outside. I thought it would be a snap and done, boy was I wrong. But hey it's on the now. Noticed a slight difference.
miketriebsch
New Member
Now how about that tail light was it easy? I literally just ordered mine.
Last edited by a moderator:
I did this all in my basement/garage i used two ratchet straps to hold the bike 1-2 inches higher then ride hight and so it would stay stright up for the exhaust install then i took a third strap and used it to hold the front of the tank up.... it was easy mode for me
Tail light was simple i should have made an install guide =(
Pretty much mounting is simple
Cut your wire plugs off your old blinkers with about 1-2 inches of wire on them so that you can wire your tail light blinker wires into them
then just wire up your tail light and throw on your plate light and its all over!!!
richierich781
New Member
Installed the two wheels adjustable levers, thats about it!
Methinks we've a contender for the FZ6R "Mod Whore" title in the works, here!
lol i know im addicted its BAD!!!
mirrors, gas cap pad, and rear sproket are in the mail haha!!!
a new rear spring, headlight mod, and handelbar mod are soon to come!!!
mirrors, gas cap pad, and rear sproket are in the mail haha!!!
a new rear spring, headlight mod, and handelbar mod are soon to come!!!
Last edited:
RooKie
New Member
Hopefully you got the Motodynamic with integrated sequential turn signals. Those are plug-and-play. Takes about 45mins to do. Other tail lights require splicing of cables:zombie: and may take longer to install. Lots of members have spliced their stuff, but I'm no electrician, so I wouldn't risk it.
RooKie
New Member
Found a piece of glass in my rear tire.
Here's a thread on the same subject. Looks like as long as there's no leak you can keep on rockin, but if you ride hard and/or have money for new tires, it may be best to replace.
Hope this helps.
Found a piece of glass in my rear tire.
I in no way endorse the following statement. Had to say it.
BUT, I've had all kinds of crap stuck in my tires. I seriously wish I had the funds to buy new tires every time it happens, but I don't.
Someone is likely thinking that you've a weak spot in your tire, and it's just waiting to blow under the worst possible circumstance. They're right. There is a hole in the tire, and that creates a weak spot, which can likely blow at the worst possible time.
However, if it's not leaking, and it's only one eighth of an inch deep? I'd ride on. Heck, I've got stuff stuck in my tire right now. Motorycle tires nowadays are soft and sticky. Stuff will get stuck.
If it really scares you, get a new tire. Otherwise? See above.
3leggeddog
New Member
Picked her up from my mechanic friend who installed the Roaring Toyz lowering link, Roaring Toyz kickstand, and Intuitive frame sliders. And then we went on our first night ride. Great way to end the day.