What did you do to your bike today?

[Spunky99]

I've been wanting my body position lower as it seems to actually be easier on my back. So I looked at my clip-ons and realized I had them all the way up as far as they would go.
Well I lowered them almost 2 inches and it feels good.....more like my old race bike....

 

[NoDoze]

Rode all over San Francisco today with my buddy and had lunch downtown. Had to take advantage of the warm 74º weather.

Spent a few minutes before the ride to take pix of Nicfitz and Giuliana.

 

[Uno979]

1980 honda cm400a

Good job

 

[flyingminno]

Went on a short canyon ride yesterday and decided to put on the camera for the ride. I sped it up because it was a little too bumpy for normal speed. If you're ever in the area should check out this road.
[ame=http://www.youtube.com/watch?v=e9Oaezbemc0]GMR Run at Twice Speed! - YouTube[/ame]

 

[LS6TT]

Added some flush turn signals, time to decide on mirrors.

 

[Uno979]

Tore into Roberts Fizzer, replaced both sprokets, rear brake rotor, new tires with dyna beads a new chain and brake pads! Not bad for half a days work

 

[CrazyCawi]

what are dyna beads?

 

[BrueThru]

what are dyna beads?

I just hope there nothing like anal beads.

Uno might just have a little bit of freak in him.

 

[KeysRider3]

DynaBeads are small glass beads that are loaded inside a tire to provide dynamic balancing. They work, provide superior balancing, and don't ugly-up your rims!

 

[linkgt]

I cleaned my bike and lubed chain

I asked this in the how to section but just hoping for a faster response here..

Are the chain slack specifications the same If you have +1 sprocket up on front? I think my chain might be too tight...as of this moment after installing +1 up front...

 

[Fizzer6R]

I cleaned my bike and lubed chain

I asked this in the how to section but just hoping for a faster response here..

Are the chain slack specifications the same If you have +1 sprocket up on front? I think my chain might be too tight...as of this moment after installing +1 up front...

yup, adjust it the same

 

[Uno979]

I just hope there nothing like anal beads.

Uno might just have a little bit of freak in him.

LoL thats Robert there... I don't work for free! Haha

Oh his front sproket after 20k miles.

 

[99vengeur]

LoL thats Robert there... I don't work for free! Haha

Oh his front sproket after 20k miles.

Yeah, the teeth were definitely starting to round forward! This should make the ride much quieter now. LOL Thanks to Alan for all his help!

Sent from my ADR6300 using Tapatalk 2

 

[BrueThru]

LoL thats Robert there...

Right, that was my attempt to suggest that he agreed with me.

Admin can't be wrong. :thumbup:

 

[Uno979]

Yeah, the teeth were definitely starting to round forward! This should make the ride much quieter now. LOL Thanks to Alan for all his help!

Sent from my ADR6300 using Tapatalk 2

No problem bromcwrenches! We work well as a team. Maybe we should open up a shop... Hmmmm

 

[Uno979]

Right, that was my attempt to suggest that he agreed with me.

Admin can't be wrong. :thumbup:

Lmao I suppose not!

 

[linkgt]

yup, adjust it the same

Thanks man. Yea.. i need to loosen the chain some then lol...

 

[spider2k]

PCV installed. now to try out some maps!

 

[BrueThru]

PCV installed. now to try out some maps!

Can't wait to hear it moving.

 

[99vengeur]

Fixed a broken FE tab that the right turn signal mounts to. I had to go back to the stock fender.

Sent from my ADR6300 using Tapatalk 2