What did you do to your bike today?

[Anthony]

Took some polish & a micro-fiber towel to mine today. Cleaned every inch of my girl...

 

[daddyrack]

cleaned the 6R and rode both of these bad boys!

 

[buzzbomb]

Took some polish & a micro-fiber towel to mine today. Cleaned every inch of my girl...

Did you pull all the plastic off? If not, it's not an "every inch" proper cleaning. Did you pull the fairings, so you can clean what's underneath?

Pulling the rear seat and grab bar, so you can get than bit of yellow cleaned on the backside. That's "every inch."

Didn't do it? I usually don't either. But to be true, that'd be "every inch."

Know what bugs me? The top of the swingarm underneath the chain guard. No way to clean it without removing the chain guard. That's where the chain lube and grit accumulate. I haven't removed the chain guard to clean it, so it's kind of caking up.

Cleaned "every inch?" Sorry to bust on you brother, but you said the words. I'm just questioning them!

 

[JT]

Speed sensor hook up is super easy. I believe the gauge wire you need is 22-24. It goes in one of the ports on the PCV and then using a tap connector or something similar splice into the pink wire of a 3 wire harness. Adv Gear Rev B uses sport map for gears 1-3 and touring 4-6. So better gas mileage and aggressive where you need it to be aggressive. It's loud with it (DBK) but certainly not obnoxious. The instructions with the PCV tell you which port is for speed sensor (I know it's the 3rd one in but not sure from which side offhand). Will literally take less than 5 minutes if you have the stuff to do it.

I made a vid of this by the way
PCV Speed Sensor wire install on a FZ6R - YouTube

 

[06330i]

I gave mine her possible final cleaning before she gets traded in for a new zx10r

 

[BKP]

- Replaced the stock seat with a new Corbin (review in another thread).

- Took a great ride with rhnatyk, another member, into the north Ga. mountains for some amazing barbecue ribs (about to be video chronicled in another thread).

- Wired in a new (dumbass) proprietary power source for a new Garmin Zumo.

 

[Weslowski]

Installed t-rex lowering link. Cut and welded kickstand. Installed proton turn signals. Stuck some bright drl in the fake air intake. Installed small eagle eye amber turn signal in the rear with the fender eliminator. Just in time for New England's snow storm!!!!

 

[Anthony]

I stared at it for a few minutes, then looked outside, then stared at it again...


WTF IS THE WARM WEATHER!

 

[Anthony]

Did you pull all the plastic off? If not, it's not an "every inch" proper cleaning. Did you pull the fairings, so you can clean what's underneath?

Pulling the rear seat and grab bar, so you can get than bit of yellow cleaned on the backside. That's "every inch."

Didn't do it? I usually don't either. But to be true, that'd be "every inch."

Know what bugs me? The top of the swingarm underneath the chain guard. No way to clean it without removing the chain guard. That's where the chain lube and grit accumulate. I haven't removed the chain guard to clean it, so it's kind of caking up.

Cleaned "every inch?" Sorry to bust on you brother, but you said the words. I'm just questioning them!

Actually, Mr. Smarty Pants, I did everything above, accept pull the decals..

 

[nismos14]

Installed t-rex lowering link. Cut and welded kickstand. Installed proton turn signals. Stuck some bright drl in the fake air intake. Installed small eagle eye amber turn signal in the rear with the fender eliminator. Just in time for New England's snow storm!!!!

You're going to love the amber eagle eyes in the FE, I did that do and it lights up entire houses from the middle of the street!!!!

 

[Weslowski]

You're going to love the amber eagle eyes in the FE, I did that do and it lights up entire houses from the middle of the street!!!!

I haven't been able to ride it like that but standing still it still looks very nice!

 

[nismos14]

It's one of my favorite mods!

 

[Weslowski]

I was gonna get the led tail light / brake light with turn signals but it doesn't seem bright and it has to much going on in a small area. So this Idea seems simple and bright!

 

[Anthony]

Received my gopro mount for my rear grab bar. Fits perfectly...


image attached.

 

[arse]

Think that would work well on the r, Anthony? I could see that being a good angle. Link ?

 

[Anthony]

Think that would work well on the r, Anthony? I could see that being a good angle. Link ?

Not allowed to link but it's on the bay. Search for...


Motorcycle Bike Bicycle Handlebar Mount For Contour GoPro+tripod + handle screw...


It was like 13 bucks delivered & is adjustable for different thickness bars. I got it for the thick grab bar on my BUSA so I can take vid of rear looking back. When I had my FZ6R I just used the suction mounts & they worked really well. Here is a vid I made using 4 or 5 angles all using the suction cups on my FZ6R


[ame=http://www.youtube.com/watch?v=RgFlYZdbM6o]FZ6R Go Pro Camera Test, 4 Different Angles - YouTube[/ame]

 

[BoneJj]

Not allowed to link but it's on the bay. Search for...


Motorcycle Bike Bicycle Handlebar Mount For Contour GoPro+tripod + handle screw...


It was like 13 bucks delivered & is adjustable for different thickness bars. I got it for the thick grab bar on my BUSA so I can take vid of rear looking back. When I had my FZ6R I just used the suction mounts & they worked really well. Here is a vid I made using 4 or 5 angles all using the suction cups on my FZ6R

nice, how is the material for 13 bucks? do you think it will hold up to abuse?

 

[Anthony]

nice, how is the material for 13 bucks? do you think it will hold up to abuse?

I do, It's very low profile & seems sturdy. For 13 bucks shipped it was worth the shot. Now I can have my gopro on my helmet & a reg cam with vid capability on the new mount... or whatever, you get what i'm sayin. Anyways, time for me to paaassssssss out..


:Sport:

 

[nismos14]

I was gonna get the led tail light / brake light with turn signals but it doesn't seem bright and it has to much going on in a small area. So this Idea seems simple and bright!

I have the led taillight and that setup is bright too, so I have double brightness!

 

[bloodypulp]

Iordered my proton flush mounts yesterday,should be here fri. cost $83 total. Are these a good investment? they look good in pic,not sure about fitment over holes in fairing.