Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 4 of 4

Thread: How to make factory bar ends work with woodcraft clip ons

  1. #1
    Junior Member
    Join Date
    Nov 2016
    Location
    Fort Bliss
    Posts
    29
    Rep Power
    0

    Default How to make factory bar ends work with woodcraft clip ons

    I have about 60 miles on this mod and they are still just as tight as when I installed them.

    Items needed
    * both bar ends
    * rubber fuel line 6 inches
    * 2x 3 inch bolts
    * 2x nuts for the bolts
    * 2x flat washers
    * cutting wheels
    * grinding wheels

    You donít have to use the same hardware I used I just had it laying around my buddies shop.

    Remove the weights

    1. Cut the threaded part off the weight


    2. Once the threaded end is cut off you will have to grind down the piece that is left till it fits in the bar. (Sorry I donít have a picture of that)

    3. Choose a drill bit to fit the size bolt you are using.


    4. Put your bolt through slide a piece of fuel line onto the bolt then place the nut on it.


    5. Snug it down but do not tighten it.

    6. Place it in the woodcraft bar it should slide all the way in.

    7. Turn the head of the bolt the nut will catch on the rubber and cause the rubber to expand.

    8. And your done for it a tug to make sure it is fully seated and not going to vibrate out.



    I am not responsible for any damage done to your motorcycle or your handle bars.

    I felt no vibration in the bars even at high speeds.


    Sent from my iPhone using Tapatalk

  2. #2
    Junior Member MadMaxx's Avatar
    Join Date
    Mar 2018
    Location
    In a van, somewhere in the SE United States
    Posts
    28
    Rep Power
    0

    Default

    how is it for vibration?

  3. #3
    Junior Member
    Join Date
    Nov 2016
    Location
    Fort Bliss
    Posts
    29
    Rep Power
    0

    Default

    Great I rode about 60 miles afterwards and didnít feel any vibration. I tried to keep as much weight as I could on it when modifying it.


    Sent from my iPhone using Tapatalk

  4. #4
    Senior Member
    Join Date
    Mar 2017
    Location
    I'm not sure
    Posts
    134
    Rep Power
    2

    Default

    Thank you thank you thank you. I'm doing this. Sick of the vibrations lol

Similar Threads

  1. Woodcraft Clip-Ons
    By Scott_Thomas in forum FZ6R Mods
    Replies: 19
    Last Post: 04-30-2018, 08:21 PM
  2. Woodcraft Clip Ons
    By Vulpine in forum FZ6R Mods
    Replies: 134
    Last Post: 03-13-2018, 09:34 AM
  3. woodcraft clip ons help
    By vengeance44 in forum FZ6R Mods
    Replies: 4
    Last Post: 05-18-2015, 08:24 PM
  4. Weighted Bar Ends for Woodcraft Clip-ons
    By rregal in forum FZ6R Mods
    Replies: 11
    Last Post: 10-19-2013, 06:27 AM
  5. Woodcraft Clip Ons
    By wllmcln in forum FZ6R Mods
    Replies: 2
    Last Post: 10-11-2013, 06:19 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •